{"product_id":"stack-speedybee-f7-v3-bl32-50a-30x30","title":"Stack SpeedyBee F7 V3 BL32 50A 30x30","description":"   \u003cstyle\u003e body { font-family: Arial, sans-serif; font-size: 14px; } for { font-family: Arial, monospace;  white-space: pre-wrap; } .highlight { font-weight: bold;}\u003c\/style\u003e\u003cpre\u003e\nStack SpeedyBee F7 V3 BL32 50A 30x30\n\nSpecifications:\nProduct Name: Flight Controller SpeedyBee F7 V3\nMCU: STM32F722\nIMU (gyroscope): BMI270\nUSB port type: Type-C\nBarometer: BMP280\nOSD chip: AT7456E chip\nBLE Bluetooth: Supported. Used to configure the Flight Controller, the built-in single combined 2.4 GHz Wi-Fi-and-Bluetooth chip.\nFirmware Flash FC wireless: Supported. Enter MENU \u0026gt; FC Firmware Flasher\nDownload\/Analyze Blackbox: Supported. Please enter MENU \u0026gt; Blackbox Analyzer\nDJI air unit connection method: Two ways are supported - 6-pin connector or direct soldering.\nDJI Air Unit 6 Pin Plug: Supported. Fully compatible with DJI O3\/RunCam Link\/Caddx Vista\/DJI Air Unit V1, no need to change any cable.\nFlash (for BlackBox): 500 MB\nBetaFlight Camera Control Pad: Yes (CC pad on front)\nPower: 3S - 6S Lipo\n5V output: 10 groups of 5V output, three +5V pads and 1 BZ+ pad (used for buzzer) on the front and 6 +5V output included in the connectors on the bottom. The total current load is 2A.\n9V output: 2 groups of 9V output, one +9V pad on the front and the other included in the connector on the bottom. The total current load is 4A.\n3.3V output: Supported. Designed for receivers with 3.3V input. Current load up to 500 mA.\n4.5V output: Supported. Designed for the GPS receiver and module, even if the FC is powered via the USB port. Current load up to 1A.\nESC Signal Pad M1 - M4 on the bottom and M5-M8 on the front.\nUART: 5 sets (UART1, UART2, UART3, UART4 (for ESC telemetry), UART6)\nESC Telemetry UART: R4(UART4)\nI2C: Supported. SDA \u0026amp; SCL pads on the front. Used for magnetometer, sonar, etc.\nLED Pad: Used for WS2812 LEDs controlled by Betaflight firmware.\nBuzzer: BZ+ and BZ- pad used for 5V buzzer\nBOOT Button: Supported.\n[AND]. Press and hold the BOOT button and power on the FC at the same time, this will put the FC into DFU mode, this is for flashing the firmware when the FC freezes.\n[B]. When the FC is powered on and in standby mode, the BOOT button can be used to control the LED strips connected to the LED1-LED4 connectors on the bottom. By default, short press the BOOT button to toggle the LED display mode. Long press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. In BF-LED mode, all LED1-LED4 strips will be controlled by Betaflight firmware.\nRSSI Input: Supported. Named as RS on the front.\nSmartPort: Not supported\nSupported Flight Controller firmware: BetaFlight (default), INAV\nTarget firmware name: SPEEDYBEEF7V3\nMounting: 30.5 x 30.5mm (hole diameter 4mm)\nDimension: 41 (L) x 38 (W) x 8.1 (H) mm\nWeight: 10.7g\n\nProduct name: SpeedyBee BL32 50A 4-in-1 ESC\nFirmware: SpeedyBee BL32 50A\nConfigurator download link: http:\/\/github.com\/bitdump\/BLHeli\/releases\nContinuous current: 50A * 4\nExplosive current: 55A (5 seconds)\nTVS protection diode: Yes\nCooler: Yes\nExternal capacitor: 1000uF Low ESR capacitor (included)\nESC protocol: DSHOT300\/600\nPWM frequency range: 16KHz-128KHz\nPower: 3-6S LiPo\nOutput power: VBAT\nCurrent Sensor: Support (Scale=490 Offset=0)\nESC telemetry: supported\nMounting: 30.5 x 30.5mm (hole diameter 4mm)\nDimension: 45.6 x 40 x 8.8 mm\nWeight: 19.2g with cooler\n\u003c\/pre\u003e","brand":"BSS","offers":[{"title":"Default Title","offer_id":51924039893328,"sku":"SB-STACK-F7V3-50A","price":108.89,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0904\/4479\/2144\/files\/48-3_48-stack-speedybee-f7-v3-bl32-50a-30x30.jpg?v=1755822519","url":"https:\/\/bsswebshop.com\/products\/stack-speedybee-f7-v3-bl32-50a-30x30","provider":"BSS Webshop","version":"1.0","type":"link"}